Clock. Safety & Driving Assistance
After pressing the "Clock" button on the touchscreen the
following settings will be available: This feature will allow the radio to sync time with a GPS
signal. To change the Sync Time setting, press the "Sync
time with GPS" button on the touchscreen until a checkmark
appears next to the setting, showing that setting has
been selected. This feature will allow you to adjust the hours. The "Sync
time with GPS" button on the touchscreen must be
unchecked. To make your selection, press the "+" or "-"
buttons on the touchscreen to adjust the hours up or
down. This feature will allow you to adjust the minutes. The
"Sync time with GPS" button on the touchscreen must be
unchecked. To make your selection, press the "+" or "-"
buttons on the touchscreen to adjust the minutes up or
down. This feature will allow you to select the time format
display setting. Press the "Time Format" button on the
touchscreen until a check-mark appears next to the "12
hrs" or "24 hrs" setting, showing that setting has been
selected. This feature will allow you to turn on or shut off the
digital clock in the status bar. To change the Show Time
Status setting press the "Show Time in Status Bar" button
on the touchscreen until a check-mark appears next to
setting, indicating that the setting has been selected. After pressing the "Safety & Driving Assistance" button
on the touchscreen the following settings will be available: The Front Collision Warning (FCW) feature provides an
audible and/or visual warning to potential forward
collisions. This feature can be enabled or disabled by
pressing the "Forward Collision Warning" button on the
center stack. The feature can be can be set to Far, Medium
or Near. The default status of FCW is the Far setting. This
means the system will warn you of a possible collision
with the vehicle in front of you when you are farther
away. This gives you the most reaction time. To change
the setting for more dynamic driving, select the Near
setting. This warns you of a possible collision when you are much closer to the
vehicle in front of you. To change
the FCW status, press and release the "Near", "Medium"
or "Far" button.
For further information, refer to "Adaptive Cruise Control
(ACC)" in "Understanding The Features Of Your
Vehicle". When this feature is selected, the paddle shifters can be
enabled or disabled. Select the "Enable" or "Disable"
button on the touchscreen. The FCW system includes Advanced Brake Assist (ABA).
When this feature is selected, the ABA applies additional
brake pressure when the driver requests insufficient
brake pressure to avoid a potential frontal collision. The
ABA system becomes active at 5 mph (8 km/h). To make
your selection, press the "Forward Collision Warning
(FCW) with Mitigation - Active Braking" button on the
touchscreen, until a check-mark appears next to setting,
indicating that the setting had been selected. For further
information, refer to "Forward Collision Warning (FCW)
With Mitigation" in "Understanding The Features Of
Your Vehicle." The ParkSense system will scan for objects behind the
vehicle when the transmission gear selector is in REVERSE
and the vehicle speed is less than 11 mph
(18 km/h). It will provide an alert (audible and/or
visual) to indicate the proximity to other objects. The
system can be enabled with Sound Only, or Sound and
Display. To change the ParkSense status, press and release
the "Sound" or "Sound and Display" button. Refer
to "ParkSense" in "Understanding The Features Of Your
Vehicle" for system function and operating information. The Rear ParkSense Chime Volume settings can be selected
from the DID or Uconnect System - if equipped.
The chime volume settings include LOW, MEDIUM, and
HIGH. The factory default volume setting is MEDIUM.
To make your selection, press the "ParkSense Rear Chime
Volume" button on the touchscreen, until a check-mark
appears next to setting, indicating that the setting had
been selected. ParkSense will retain its last known configuration
state through ignition cycles. To make your selection, press the "Rear ParkSense Braking
Assist" button on the touchscreen, until a check-mark
appears next to setting, indicating that the setting had
been selected. When this feature is selected, the exterior side view
mirrors will tilt downward when the ignition is in the
RUN position and the transmission gear selector is in the
REVERSE position. The mirrors will move back to their
previous position when the transmission is shifted out of
REVERSE. To make your selection, press the "Tilt Side
Mirrors In Reverse" button on the touchscreen, until a
check-mark appears next to setting, indicating that the
setting had been selected. When this feature is selected, the Blind Spot Alert feature
Provides alerts, visual and/or audible, to indicate objects
in your blind spot. The Blind Spot Alert feature can be
activated in "Lights" mode. When this mode is selected,
the Blind Spot Monitor (BSM) system is activated and
will only show a visual alert in the exterior mirrors.
When "Lights & Chime" mode is activated, the Blind Spot Monitor (BSM) will show
a visual alert in the
exterior mirrors as well as an audible alert when the turn
signal is on. When "Off" is selected, the Blind Spot
Monitor (BSM) system is deactivated. To change the
Blind Spot Alert status, press the "Off," "Lights" or
"Lights & Chime" button on the touchscreen.
NOTE: If your vehicle has experienced any damage in
the area where the sensor is located, even if the fascia is
not damaged, the sensor may have become misaligned.
Take your vehicle to an authorized dealer to verify sensor
alignment. Having a sensor that is misaligned will result
in the BSM not operating to specification. Your vehicle may be equipped with the ParkView Rear
Back Up Camera Active Guidelines that allows you to see
active guidelines over the ParkView Back up camera
display whenever the gear selector is put into REVERSE.
The image will be displayed on the radio touchscreen
display along with a caution note to "check entire surroundings"
across the top of the screen. After five seconds,
this note will disappear. To change the mode status,
press the "ParkView Backup Camera Active Guidelines"
button on the touchscreen, until a check-mark appears
next to setting, indicating that the setting had been
selected. When the vehicle is shifted out of REVERSE (with camera
delay turned OFF), the rear camera mode is exited and
the navigation or audio screen appears again. When the
vehicle is shifted out of REVERSE (with camera delay
turned ON), the rear view image with dynamic grid lines
will be displayed for up to 10 seconds after shifting out of
REVERSE unless the forward vehicle speed exceeds
8 mph (12 km/h), the transmission is shifted into PARK
or the ignition is switched to the OFF position. To set the
ParkView Backup Camera Delay press the "Controls" button on the touchscreen, the
"settings" button on the
touchscreen, then the "Safety & Driving Assistance"
button on the touchscreen. Press the "Parkview Backup
camera Delay" button on the touchscreen to turn the
ParkView Delay ON or OFF. When this feature is selected, the system will automatically
activate the windshield wipers if it senses moisture
on the windshield. To make your selection, press the
"Rain Sensing" button on the touchscreen, until a checkmark
appears next to setting, indicating that the setting
had been selected. When this feature is selected, the Hill Start Assist (HSA)
system is active. Refer to "Electronic Brake Control
System" in "Starting And Operating" for system function
and operating information. To make your selection, press
the "Hill Start Assist" button on the touchscreen, until a
check-mark appears next to setting, indicating that the
setting had been selected. The Steering Feel Options feature will allow you to adjust
the steering effort and feel. Press the "Sport" button on
the touchscreen to provide the greatest amount of steering
feel, requiring the highest amount of steering effort.
Press the "Normal" button on the touchscreen to provide
greater steering feel, requiring greater steering effort.
Press the "Comfort" button on the touchscreen to provide
a balance of steering feel and steering effortClock
Safety & Driving Assistance
Dodge Durango (WD) 2011-2024 Owners Manual
Categories
